4.72
Alarm systems
Camera surveillance
Intercom access systems
Black Friday Deals
JA-151M
Service explanation for JA-151M
Wireless mini magnetic contact
This product is part of the JABLOTRON JA-100 alarm system. It is used to detect the opening of a door, window, etc. The detector is powered from a miniature battery and has an optional response (pulse or status response). The product must be installed by a trained technician with a valid Jablotron certificate.
Installation
Choose a suitable place for installation. The detector reacts to the distance increase of the permanent magnet. The magnet can be left or right. Mount the transmitting part on the fixed part of the door (window) and the magnet on the moving part. Avoid placing directly on metal objects (they negatively affect the operation of the magnetic sensor and also radio communication).
Figure: 1 – screen drop-in clamp; 2 – red activation signal light
1. Open the detector's screen by pressing the drop-in clip (1).
2. Screw the plastic back panel onto the fixed part of the door (window).
3. Screw the permanent magnet onto the moving part of the door (window). The distance between the magnet and the transmitting part should be as short as possible. The distances from the magnet that activate the detector are shown in the picture.
Figure: detector activation distances
4. Learn the detector in the control panel (receiver). The prerequisite for reading into the system is the presence of a JA-110R radio module in the system. In the F-Link program, select the desired position on the Peripherals card and by choosing Read in you enable the learning mode. The learning signal is sent at the moment of inserting the battery into the detector.
5. After learning, put the detector on the back wall.
6. Set the function of the detector using the F-Link program.
7. Test the detector for proper operation.
Image: 3 – serial number; 4 - tamper switch; 5 – battery; 6 – permanent magnet; 7 – magnetic pickup; 8 – red signal light of detector activation; 9 – alternative placement of the permanent magnet
Comments:
If you teach the detector in the receiver after the battery has already been connected, first disconnect it, then press and release the screen contact (4) (the residual energy is used up) and only then execute the learning mode.
The detector can be enrolled into the system by entering its serial number (3) through the F-Link program or from the keypad (or barcode reader). All numbers below the barcode are entered (1400-00-0000-0001).
Set detector properties
The detector has 2 modes indicated by one or two flashes of the signal light when the battery is inserted.
• One flash means the detector will report opening and closing, track and report its own status (status response).
• Two flashes means a pulse response, so the detector will only report activation (opening of the door or window).
The working mode is determined at battery insertion, by pressing and holding the contact switch from the detector's screen, inserting the battery and releasing the switch 3-5 seconds after inserting the battery. The detector will then flash once or twice, depending on the mode just selected. The factory setting is the status response.
Other setting of the functions is done using the F-Link program, in the Peripherals card. Here you can set the type of reaction with which the system will respond to activation of the learned detector, the section in which it will be read, and possibly also the PG output that can be controlled by the detector. The Delayed A response is set from the factory (gives an entry and exit delay).
Detector testing
For 15 minutes after closing the detector's screen, the test mode is enabled, with each activation transmitted and indicated by the signal light on the detector's screen. The signal from the detector and its activations can be monitored in service mode of the control panel through the F-Link program in the Diagnostics window.
Replace battery in detector
The system automatically reports as soon as the battery runs out. Before replacing the battery in the detector, the system must be switched to Service mode (otherwise a tamper alarm will be triggered).
Technical parameters
Power supply lithium battery, type CR2032 (3.0V, 220 mAh)
Typical battery life approx. 2 years (max. 20 activations/day)
Communication band 868.1 MHz, protocol JABLOTRON
Communication range approx. 200m (direct visibility)
Detector dimensions 55 x 26 x 16 mm
Magnet dimensions 55 x 16 x 16 mm
Classification grade 2
in accordance with CSN EN 50131-1, CSN EN 50131-3
Environment in accordance with CSN EN 50131-1 II. inside, general
Operating temperature range -10 to +40 °C
Further complies with CSN EN 50130-4, CSN EN 55022
The JA-151M product has been designed and manufactured in accordance with the applicable provisions: Government Decree No. 616/2006 Coll., provided that it is used as intended.
Note: Although this product does not contain any harmful materials, do not dispose of it with household waste, but hand it in at the collection point designated for electronic waste.
Installation
Choose a suitable place for installation. The detector reacts to the distance increase of the permanent magnet. The magnet can be left or right. Mount the transmitting part on the fixed part of the door (window) and the magnet on the moving part. Avoid placing directly on metal objects (they negatively affect the operation of the magnetic sensor and also radio communication).
Figure: 1 – screen drop-in clamp; 2 – red activation signal light
1. Open the detector's screen by pressing the drop-in clip (1).
2. Screw the plastic back panel onto the fixed part of the door (window).
3. Screw the permanent magnet onto the moving part of the door (window). The distance between the magnet and the transmitting part should be as short as possible. The distances from the magnet that activate the detector are shown in the picture.
Figure: detector activation distances
4. Learn the detector in the control panel (receiver). The prerequisite for reading into the system is the presence of a JA-110R radio module in the system. In the F-Link program, select the desired position on the Peripherals card and by choosing Read in you enable the learning mode. The learning signal is sent at the moment of inserting the battery into the detector.
5. After learning, put the detector on the back wall.
6. Set the function of the detector using the F-Link program.
7. Test the detector for proper operation.
Image: 3 – serial number; 4 - tamper switch; 5 – battery; 6 – permanent magnet; 7 – magnetic pickup; 8 – red signal light of detector activation; 9 – alternative placement of the permanent magnet
Comments:
If you teach the detector in the receiver after the battery has already been connected, first disconnect it, then press and release the screen contact (4) (the residual energy is used up) and only then execute the learning mode.
The detector can be enrolled into the system by entering its serial number (3) through the F-Link program or from the keypad (or barcode reader). All numbers below the barcode are entered (1400-00-0000-0001).
Set detector properties
The detector has 2 modes indicated by one or two flashes of the signal light when the battery is inserted.
• One flash means the detector will report opening and closing, track and report its own status (status response).
• Two flashes means a pulse response, so the detector will only report activation (opening of the door or window).
The working mode is determined at battery insertion, by pressing and holding the contact switch from the detector's screen, inserting the battery and releasing the switch 3-5 seconds after inserting the battery. The detector will then flash once or twice, depending on the mode just selected. The factory setting is the status response.
Other setting of the functions is done using the F-Link program, in the Peripherals card. Here you can set the type of reaction with which the system will respond to activation of the learned detector, the section in which it will be read, and possibly also the PG output that can be controlled by the detector. The Delayed A response is set from the factory (gives an entry and exit delay).
Detector testing
For 15 minutes after closing the detector's screen, the test mode is enabled, with each activation transmitted and indicated by the signal light on the detector's screen. The signal from the detector and its activations can be monitored in service mode of the control panel through the F-Link program in the Diagnostics window.
Replace battery in detector
The system automatically reports as soon as the battery runs out. Before replacing the battery in the detector, the system must be switched to Service mode (otherwise a tamper alarm will be triggered).
Technical parameters
Power supply lithium battery, type CR2032 (3.0V, 220 mAh)
Typical battery life approx. 2 years (max. 20 activations/day)
Communication band 868.1 MHz, protocol JABLOTRON
Communication range approx. 200m (direct visibility)
Detector dimensions 55 x 26 x 16 mm
Magnet dimensions 55 x 16 x 16 mm
Classification grade 2
in accordance with CSN EN 50131-1, CSN EN 50131-3
Environment in accordance with CSN EN 50131-1 II. inside, general
Operating temperature range -10 to +40 °C
Further complies with CSN EN 50130-4, CSN EN 55022
The JA-151M product has been designed and manufactured in accordance with the applicable provisions: Government Decree No. 616/2006 Coll., provided that it is used as intended.
Note: Although this product does not contain any harmful materials, do not dispose of it with household waste, but hand it in at the collection point designated for electronic waste.
